RobustPCBWhere Robust Design Starts
الحاسباتEnglishUpgradeتسجيل الدخولإنشاء حساب

ما الجديد

سجل التغييرات الكاملالمحرّك 1.18.3

LC Resonance & Damping

الإشارة والتوقيت

Resonant frequency, Q and characteristic impedance of an LC pair, and the resistance that damps it.

هذه الصفحة غير مترجمة بالكامل بعد. الأجزاء غير المترجمة معروضة بالإنجليزية.

المدخلات

H
10 µH
F
22 µF
Inductor DCR + capacitor ESR + trace
Ω
50 mΩ
A resistive load across C; gives the loaded Q
Ω
The target when solving for L or C
Hz

النتائج

1 للمراجعة
Resonant frequency f0

بلا حكم: a resonant frequency has no pass or fail. Damping decides whether the network behaves: see the quality factor below.
10.73kHz
Characteristic impedance Z0

√(L/C)
674.2mΩ
Quality factor Q

damping ratio ζ = 0.037
13.48
كل النتائج (4)
Step overshoot
89.0%
Peak gain at f₀
22.6dB
Series R for Q = 1
674.2mΩ
Critical damping R

ζ = 1, no overshoot
1.348Ω
Q = 13.5: this network rings (about 89 % overshoot, 23 dB of peaking at 10.73 kHz). Raise the series resistance to 674.2 mΩ for Q = 1, or add an R–C damping leg. An R–C leg across the capacitor damps the peak without the DC loss of a series resistor.
|Vout/Vin|

إلى أي حد نعرف هذا الرقم

يُقاس مقابل

3 حالات في هذا الموقع تقارن هذه الحاسبة بأرقام حُسبت من دون كودها. اطّلع على الحساب.

هذه أداة مساعدة للتصميم. يبقى المهندس مسؤولاً عن التصميم وعن قراءة المرجع القياسي نفسه حيث يهم ذلك.

المسح البارامتري

غيّر مدخلاً واحداً على مدى، وشاهد الإجابة والحكم والهامش عند كل خطوة، جدولاً ومنحنى.Pro

أسوأ الحالات

أضف التفاوتات إلى المدخلات لتحصل على النطاق المضمون حول الإجابة الاسمية، لا الحالة النموذجية وحدها.Pro

Circuit

المبدأ

An inductor and a capacitor exchange energy at a frequency set by √(LC). How hard they ring depends on the loop resistance compared with the characteristic impedance √(L/C). That ratio decides whether a filter behaves.

Resonant frequency
f0=12πLCf_0 = \frac{1}{2\pi\sqrt{LC}}
Characteristic impedance
Z0=LCZ_0 = \sqrt{\frac{L}{C}}
The reactance of L, and of C, at f0. Size damping resistance against this, not against the load.
Quality factor and damping (series RLC)
Q=Z0Rs=1RsLCζ=12Q=Rs2Z0Q = \frac{Z_0}{R_s} = \frac{1}{R_s}\sqrt{\frac{L}{C}} \qquad \zeta = \frac{1}{2Q} = \frac{R_s}{2 Z_0}
Step overshoot
Mp=e−πζ/1−ζ2×100  %M_p = e^{-\pi\zeta/\sqrt{1-\zeta^{2}}}\times 100\;\%
Bandwidth
BW=f0QBW = \frac{f_0}{Q}
Critical damping
Rs=2Z0  ⇒  ζ=1  (no overshoot)R_s = 2 Z_0 \;\Rightarrow\; \zeta = 1 \;\t{(no overshoot)}
  • Z0Z_0characteristic impedance of the LC pair
  • RsR_stotal series resistance: inductor DCR + capacitor ESR + copper
  • ζ\zetadamping ratio; ζ < 1 rings, ζ = 1 is critical, ζ > 1 is overdamped
تفاصيل إضافية

Input filters and negative resistance

A switching converter draws constant power, so its input looks like a negative resistance, −V²/P. If the filter's output impedance at resonance exceeds that magnitude, the supply oscillates at the filter's resonant frequency. This is Middlebrook's criterion. The cure is damping, not more filtering.

Damp without wasting power. Put the damping resistor in series with a separate electrolytic or polymer capacitor, in parallel with the main ceramic. It carries no DC current but dominates at resonance. Typical values: Cdamp ≈ 3–5 × Cmain, Rdamp ≈ Z₀.

The same maths elsewhere

  • Snubbers. Switch-node ringing is the layout inductance against the FET's Coss. Measure the ring frequency, add a known capacitor and measure again. The shift gives L and C, and the snubber resistor is R = √(L/C).
  • Crystals and tank circuits, where you want Q high rather than low.
Further reading: R. D. Middlebrook, "Input filter considerations in design and application of switching regulators" (1976).

إصدار المحرك ⁨1.18.3⁩